Beginner's Plumbing: What You Need for Installing a Bathtub
Call TodayThis article down below in relation to How to Install a Bathtub Yourself is relatively interesting. You should keep reading.
Mounting a bath tub isn't exactly rocket science, but it does require solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately difficult project. If the old bathtub is conveniently easily accessible, the task can move easily; if you have to open up a wall to remove the old bathtub and also position the new bath tub, the job is much harder. In either situation, the job is within a home handyman's skills, although you will need a helper to vacate the old bathtub as well as embeded in the new one. Make sure you have qualified on your own for the job as well as fit attempting it. Instead of employing a contractor to take control of a halfway-completed project, it is far better to take into consideration utilizing one before you start. Chances are you may require a specialist plumber to make tube connections.
This post will aid you install a new bathtub in your restroom if you have actually currently purchased a brand-new tub and do not require to transform the plan of your previous water system pipelines.
Your tools as well as material checklist need to make up the following:
Planning for the Installment
To start with, the supporting frame supplied with the bath ought to be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to make sure that if the tap features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps unit to prevent stress on the bathtub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its final setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, then the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be quite problematic due to the restricted access that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this process. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any old securing substance.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the called for position. The wooden boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the spirit level as well as readjusting the feet on the tub up until the level reads level.
To set up taps, fit all-time low of the furthest versatile faucet port to the ideal supply pipe by making a compression join; then do the same for the other faucet.
Activate the water supply and also inspect all joints and new pipework for leaks and tighten them if needed. Fill the tub as well as also inspect the overflow electrical outlet and the typical outlet for leakages.
Ultimately, take care of the bath paneling as described in the producer's user's manual. Tiling and also sealing around the tub must wait till the bathtub has actually been used a minimum of once as this will settle it right into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the mounting opening in the bath/basin making certain that the washing machines remain in location between the tap and also the sink. Secure the faucet in position with the supplier supplied backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap adapters. The previous kind ought to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture an inflexible seal, triggering the water to pass through the wall in between the bathroom and also the tiling, bring about difficulties with dampness and also feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and cartridges, and can securing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill up the tub with water prior to securing, to enable the activity experienced when the tub remains in usage. The sealer can break relatively very early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that write up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a lookup on the internet. You should take the opportunity to distribute this post if you liked it. I am grateful for your time. Visit again soon.
Schedule A Free Estimate